GF4 Ti 4200 + FF7 FSAA

[ye-roon]

I got a GF4 ti 4200. thus i tried the code change n stuff:

this piece of code
Code: [Select]

Required05 = 200h,

is replaced by this
Code: [Select]

FSAAMode06=ff06 FSAAMode0C=ff0c FSAAMode0D=ff0d

using that method. SO doesn't this mean that there isn't a REquired05 ne more, or in other words, there is nothing for 2 x 2 mode to draw its requirements from. The code replacing also doesn't work for me in this format. i still have the sameweird lines and ugly backgrounds, so far i tried 45.23 and 52.13 drivers, will try 53.03 now and after that 56.xx

screens from 56.64
this is with the changed code
http://stud.hro.nl/0549792/2x2metback.jpg
http://stud.hro.nl/0549792/2x2metbtl.jpg

this is with original code
http://stud.hro.nl/0549792/2x2zonderback.jpg
http://stud.hro.nl/0549792/2x2zonderbtle.jpg

If you use nv17 (or above), fsaamode05/06/0C/0D should be ok with FF7pc.

what is nv17??

and i tried all those fsaamodes and they all seem to worsen the farther the number goes

oh i found something out..

i don't know what all the technical stuff means suff but:
when i put aa to 2 x 1 the horizontal lines are gone, but the vertical lines are not. when i use  1 x 2 the vertical lines are gone horizontal lines are not. also i uninstalled the 52.16 before installing the 53.03 drivers and RT still says some versions of the drivers are 52.16 :x well ne way all these AA modules don't work for me afaik (

oh and if someone has RT 14.1 installer or a link to it

 

[Srethron Askvelhtnod]

what is nv17??

Now there's a question I haven't seen in about two years.
The short answer is this:
nv17 == all nVidia chips in the GeForce 4 MX series
nv25 == all nVidia chips in the GeForce 4 TI series

So you have an nv25. Which is a good thing, since nv17 cards aren't as good as nv25 (no nfiniteFX-engine, no directX 8 support, etc.)

Based on this info, when you hear people talking about nv30, I trust you'll be able to figure out what cards they're referring to.

 

[halohalo]

I got a GF4 ti 4200. thus i tried the code change n stuff:

this piece of code
Code: [Select]

Required05 = 200h,

is replaced by this
Code: [Select]

FSAAMode06=ff06 FSAAMode0C=ff0c FSAAMode0D=ff0d

using that method. SO doesn't this mean that there isn't a REquired05 ne more, or in other words, there is nothing for 2 x 2 mode to draw its requirements from. The code replacing also doesn't work for me in this format. i still have the sameweird lines and ugly backgrounds, so far i tried 45.23 and 52.13 drivers, will try 53.03 now and after that 56.xx

screens from 56.64
this is with the changed code
http://stud.hro.nl/0549792/2x2metback.jpg
http://stud.hro.nl/0549792/2x2metbtl.jpg

this is with original code
http://stud.hro.nl/0549792/2x2zonderback.jpg
http://stud.hro.nl/0549792/2x2zonderbtle.jpg

You need to enable 8bit paletted textures with RivaTuner.